西班牙语Seven common faults, inspection and maintenance of bottle blowing equipment
Seven common faults, inspection and maintenance of bottle blowing equipment
24. Trouble: The timing of the bottle sending finger is wrong, and the finger of the welding ring machine clamps the bottle from time to time.
Inspection: 1. Check whether the position of the blue square proximity switch on the sprocket on the south side of the bottle clamp chain of the welding ring machine is loose. This switch is very sensitive and must be adjusted in small increments until the bottle can not be dropped during the adjustment. 2. Check whether the bottom coupling of the blue circular encoder on the north sprocket of the bottle clamp chain of the welding ring machine is broken and there is a large gap (small cracks will not affect the bottle delivery), replace it. 3. Check whether the bottle clamping chain of the welding ring machine is aligned with the position of the bottle feeding finger, and whether the opening of the individual bottle clamping finger is too small or too biased, and adjust the opening position. 4. At the same time, check the alignment of the bottle-feeding finger in the position of the bottle-reversing finger, and check the alignment of the bottle-feeding finger on the bottle clamping chain side of the welding ring machine and the position of the bottle clamping finger. It is necessary to ensure that the bottle-reversing finger and the welding ring The fingers of the machine clamp the bottle in a straight line. And check the degree of the transfer of the bottle-feeding finger with the bottle-reversing finger and the finger of the welding ring machine clamping bottle. The bottle-feeding cannot be too deep or too shallow, and the bottle will fall. You can adjust the limit buffer of the piston rod nut of the bottle feeding cylinder or the bottle holding finger to make the center of the bottle holding finger and the bottle holding finger in a straight line.
25. Trouble: Individual bottles of the welding ring machine do not blow, which seriously affects the qualification rate of the welding ring.
Inspection: 1. Check whether the bottle pressing block can effectively seal the bottle mouth to prevent air leakage when the bottle clamp chain of the welding ring machine and the main plate of the welding ring machine transfer bottles. 2. Check whether the output intermediate relay corresponding to the air blowing in the power distribution cabinet can work normally; you can change the intermediate relay to try or change the normally open contacts of the intermediate relay to a group to determine the reason for not blowing.
24. Trouble: The timing of the bottle sending finger is wrong, and the finger of the welding ring machine clamps the bottle from time to time.
Inspection: 1. Check whether the position of the blue square proximity switch on the sprocket on the south side of the bottle clamp chain of the welding ring machine is loose. This switch is very sensitive and must be adjusted in small increments until the bottle can not be dropped during the adjustment. 2. Check whether the bottom coupling of the blue circular encoder on the north sprocket of the bottle clamp chain of the welding ring machine is broken and there is a large gap (small cracks will not affect the bottle delivery), replace it. 3. Check whether the bottle clamping chain of the welding ring machine is aligned with the position of the bottle feeding finger, and whether the opening of the individual bottle clamping finger is too small or too biased, and adjust the opening position. 4. At the same time, check the alignment of the bottle-feeding finger in the position of the bottle-reversing finger, and check the alignment of the bottle-feeding finger on the bottle clamping chain side of the welding ring machine and the position of the bottle clamping finger. It is necessary to ensure that the bottle-reversing finger and the welding ring The fingers of the machine clamp the bottle in a straight line. And check the degree of the transfer of the bottle-feeding finger with the bottle-reversing finger and the finger of the welding ring machine clamping bottle. The bottle-feeding cannot be too deep or too shallow, and the bottle will fall. You can adjust the limit buffer of the piston rod nut of the bottle feeding cylinder or the bottle holding finger to make the center of the bottle holding finger and the bottle holding finger in a straight line.
25. Trouble: Individual bottles of the welding ring machine do not blow, which seriously affects the qualification rate of the welding ring.
Inspection: 1. Check whether the bottle pressing block can effectively seal the bottle mouth to prevent air leakage when the bottle clamp chain of the welding ring machine and the main plate of the welding ring machine transfer bottles. 2. Check whether the output intermediate relay corresponding to the air blowing in the power distribution cabinet can work normally; you can change the intermediate relay to try or change the normally open contacts of the intermediate relay to a group to determine the reason for not blowing.
